Wear-resistant washable semi-matt wall paint
Colour: White
Consumption: 6-10 m2/L
Drying time:At the temperature of +20 °C and the relative humidity of 50%, the coat dries and the surface is ready for the application of another coat in 1–2 hours. If the temperature is lower and the humidity is higher, the drying takes longer accordingly.
Volume / weight: 0,95L-2,85L-4,75L-9,5L-19L
Acrylate water-borne paint providing maximum application comfort and resulting in wear-resistant surfaces.
Maximum permissible VOC content for the product (subcat. a): 30g/L; maximum VOC content in the product:
≤ 15 g/L.
Gloss:
Wash resistance:
Painting walls and ceilings in rooms with high performance requirements and where frequent wet cleaning is required: residential and office rooms, children’s rooms, entrance halls, corridors, stair wells, public spaces, garages, workshops, cafes, restaurants, stores, clubs, etc.
Is not suitable for application on floors, doors and furniture.
New or previously painted surfaces made of concrete, aerated concrete, gypsum board, primed wood chipboard or wood fibre board; brick, surfaces filled with putty and plastered and surfaces covered with glass fibre wallpaper or other paintable finishing materials.
Previously unpainted surfaces: Clean the surface, removing dirt and dust. Apply a suitable putty from the FILLER line: Face Filler (deep cracks), Aqua Filler (wet rooms), Fine Filler and Fine Pro Filler (finishing). Sand the filled surface to make it even and remove sanding dust. Prime filled, porous or unevenly porous surfaces with Aquastop or Tiefgrund moisture barrier. Follow the product instructions for use. Prime the surfaces with water-borne priming paint Flat to even out the surface absorption capacity, increase the durability of the painted surface and decrease the consumption of the top coat paint.
Previously painted surfaces: The painted surface must be cleaned from loose and peeling material, grease, dust and other impurities. If mould removal is necessary, use Biotol E or Biotol Spray (follow the product instructions for use). To clean the surfaces that are very dirty or have soot, water, nicotine or grease stains, wash the surface with a EasyClean and leave to dry. Then prime with the isolating paint Objekt. Before painting durable old alkyd surfaces, sand them until they are matt and remove sanding dust thoroughly. Use a putty from the FILLER line to fill cracks, holes and uneven areas. Sand the filled surface to make it even and remove sanding dust. Prime filled surfaces with Aquastop or Tiefgrund moisture barrier to reduce porosity. Prime the surfaces with water-borne priming paint Flat to decrease the consumption of the top coat paint and improve coverage. When using very dark or bright tones of Akrit 12, we recommend priming with the paint of a similar colour..
Stir the paint thoroughly before application. The paint can be diluted with water in the amount of up to 5% of its volume for the application of the first coat. Apply 2 coats with a roller or spray gun at the temperature between 10 °C and 25 °C and relative humidity not exceeding 80%. Avoid application in draughty places and at high air temperature (over +25 °C). When painting, make sure to keep a wet edge.
The coating reaches its peak wear resistance in about 4 weeks; in the meantime, treat the surface with care until its hardness and wear resistance have reached their peak levels. If necessary, the surface can be lightly wiped with a soft sponge or cloth approximately 48 hours after paint application. We recommend using water and neutral or medium alkaline detergents (pH below 9). Do not use organic solvents, abrasive cleansers and hard scrubbing brushes or sponges. Extensive rubbing may make the surface glossy. We recommend using Biotol E and Biotol Spray to remove mould.
Wash with soap and water after completing work.
Store and transport in intact containers at the temperature between +5°С and +30°С. Protect from exposure to freezing and direct sunlight.
The information concerning the product is based on the results of laboratory tests and practical use of the product depending on the location and conditions of its use. As the manufacturer, we guarantee the quality of the product and provide the best recommendations for its appropriate application. As the manufacturer, we cannot control the conditions and circumstances of product transportation, storage and application and numerous other factors that affect its use. Thus, we shall not bear responsibility for the damage caused by ignoring the instructions for use or transportation, by noncompliance with storage conditions and timeframes or by inappropriate application of the product. The manufacturer reserves the right to alter product information at their discretion without prior notice.
Kulu arvutatakse 1 kihile
