Highly opaque deep-matt ceiling paint
Colour: White
Consumption: Consumption on the absorbing surface of 8…10 m²/L, consumption of non-absorbent surface of 11…14 m²/L. For painting 1 m² s required approximately 100…150 ml of paint, depending on the surface.
Drying time: The surface is ready for the application of another coat in 2 hours. The surface is fully dry in 12 hours at the temperature of +23°C and the relative humidity of 50%
Volume / weight: 0,9L – 2,7L – 9L
Latex water-borne deeply matt highly opaque ceiling paint for dry rooms intended for standard conditions of use.
Maximum permissible VOC content for the product (subcat. a): 30g/L; maximum VOC content in the product: <10 g/L.
Gloss:
Wash resistance:
Indoor load class:
Painting ceilings in dry residential and public indoor areas (living-rooms, bedrooms, offices, hotels, etc.). Can be used for priming before the application of matt and semi-matt water-borne paints (Akzent, Mattilda, Akrit, etc.) on walls and ceilings in dry indoor areas.
Surfaces previously painted with latex, alky or oil-based paints or new surfaces made of concrete, aerated concrete, gypsum board; brick; surfaces finished with putty or plastered and surfaces covered with glass fibre wallpaper or other rolled finishing materials. For interior use.
The surface to be painted must be carefully cleaned from loose or peeling material, dirt, grease and dust. Remove old chalk surface completely. Sandpaper durable alkyd substrates until they are matt and remove the dust thoroughly. If the surface is very dirty, wash it with EasyClean. Use a Fine Filler putty to fill cracks and dents or smooth the surface. We recommend using FINE-PRO FILLER as the finishing layer to even out the surface. Use Aquastop to prime surfaces that give up dust and surfaces with uneven absorption. Please follow the product application manual.
Stir the paint thoroughly before application. Does not to be diluted when used as a top coat or applied with a roller. Apply with a roller or spray gun at the temperature between +10 °C and +25 °C and relative air humidity below 80%. Apply a level uniform coat. The second coat might be needed for surfaces in a contrasting colour. When using as a primer or applying with a spray gun, dilute the paint with water in the amount of up to 5% of its volume; use the 0.017–0.021” spray gun nozzle. One coat will generally be sufficient. Try to maintain a wet edge in the process of painting. In case the paint job is carried out in adverse conditions (draughts, the use of heating appliances, high temperature or low air humidity), we recommend using the Time+ slow-dry agent in the amount of up to 3% of the paint volume. Please follow the product application manual.
Under normal conditions, the paint coat reaches its peak hardness in 3…4 weeks, after which the painted surface can withstand cleaning. Use lukewarm water and neutral or mildly alkaline detergents (pH below 9) and a soft microfiber cloth for cleaning. Do not use organic solvents. Do not use abrasive tools or detergents, stiff brushes or rough sponges. Excessive rubbing may make the surface glossy. Wipe the surface dry after wet cleaning.
Roller (pile length: 10-14 mm), airless spray gun, brush.
Wash with soap and water after completing work.
Store and transport in intact containers at the temperature between +5…30 °С. Protect from exposure to freezing and direct sunlight.
The information concerning the product is based on the results of laboratory tests and practical use of the product depending on the location and conditions of its use. As the manufacturer, we guarantee the quality of the product and provide the best recommendations for its appropriate application. As the manufacturer, we cannot control the conditions and circumstances of product transportation, storage and application and numerous other factors that affect its use. Thus, we shall not bear responsibility for the damage caused by ignoring the instructions for use or transportation, by noncompliance with storage conditions and timeframes or by inappropriate application of the product. The manufacturer reserves the right to alter product information at their discretion without prior notice.
Consumption is calculated for 1 layer
